Laurel Update

So Since taking ownership of the Laurel, what’s been happening?

Well, I wanted to get it to a drift day ASAP, I’m not one for hanging around but at the same time there were a few things that needed adressing before I could take it out on track.

Following the coilpack issues with the Skyline I decided to treat the RB in the Laurel to some new coil packs in the form of Yellow Jackets coilpacks. The installation was extremely simple, just unbolt the old ones and bolt in these, I also replaced the spark plugs for good measure.

While I was working in the engine bay I decided to do a little bit of tidying up starting with addressing the tatty looking rocker covers, they looked like they’d had something spill on them removing most of the paint at some point in the past, so while the engine is apart why not!

I had some spray paint knocking around in the shed so after a good clean and scuff I hit them with a few coats of high temp paint, followed by some fancy sparkle flake stuff I had knocking around and finally a few coats of clear lacquer before replacing the gaskets with new and re-fitting them.

Once the rocker covers had been refitted I realised that the cam cover now looked scruffier than ever, so that was the next thing to get the tidy up treatment.

Then it was time to do a bit of simplifying, as when we initially fitted a catch can there were a bunch of pipes that needed plugging, one of these pipes no longer went anywhere and so could be removed, it was weleded to another pipe that’s still needed so I broke out the angle grinder and got choppy! Sadly I forgot to take photos of this bit!

Since we first got the car it had had an aftermarket grounding kit fitted to it, this thing looked messy but at the time we didn’t want to touch it, it was working ant thats all that mattered. Sadly as time went on we found that were coming up against other problems that could be caused by bad grounding.

After a bunch of fixes that worked temporarily I decided it was time to remove the grounding kit (which by the way had two out of five of the ground wires going back to the negative terminal on the battery!) and try to find the source of the issue.

It didn’t take long, while I was working on the hot side of the engine I found the remains of a factory ground strap going from the top of the manifold to the chassis it had snapped near the manifold, I jumped online and bought a replacement and that sorted it.

It made sense while I was working in that area to finally delete the charcoal cannister too, doing this seems to be common on most drift and performance Jap cars and its a surprisingly easy job to do.

Now that the engine was back together, it was time to turn my attention to the interior. At the last drift day the gauges for oil temp, water temp and oil pressure stopped working, I was initially hoping that that sorting the grounding issues on the car would fix this too but it didn’t! Thankfully this was another issue where it didn’t take long to find the root cause.

The power for these gauges was taken from the switched power on the cigarette lighter, and the fuse for the lighter had blown so replacing the fuse fixed the gauges too. At some point I will find a better location to get switched power for these gauges but for now at least until after I’ve been to the track I’ll leave things as they are.

I also tried to get the stereo working again but sadly this wasn’t happening, I’m not sure why it isn’t working as its getting power so must be a grounding issue but all my attempts to ground it were a failure. Thankfully having music isn’t a must for a drift day.

After a bit of tidying up it was time to fit the new seats, I’d had these sitting around since they had first been released, I was originally going to fit them to the Skyline but when I decided to let that go I just HAD to keep them for the Laurel instead. I’m talking of course about my Shirts Tucked In (https://store.shirtstuckedin.com/) bucket seats.

I don’t think I need to talk about how I fitted the seats as most have fitted a bucket seat at some point. I was surprised, however at just how much these brightened up the interior! Coupled with my Yashio Factory harness bought from Otaku Garage they look amazing!! I really need to get a second one of these harnesses at some point for the passenger side!

So now the car is ready to take to the track, it doesn’t have a body kit yet, so to some its going to look a bit like a missile car but thats only temporary! The main thing is I start getting to grips with driving this thing hard!